Frage zu einem Eintrag in der Notes.ini

[Yvi]

Hallo,

ich hätte mal eine Frage zu einem Eintrag in der Notes.ini:

was bedeutet der Parameter: "debugwinsplitterpos=xxx"  

Vielen Dank schonmal.

Wir haben Server- Version 5.0.10, Client 4.5.7h, 4.6.5 und 5.0.11

Gruß Yvi

[koehlerbv]

Die Knowledgebase äussert sich nicht dazu, nicht einmal DRCC - da steht nur "Pending" und das es für den Designer sei. Es scheint aber mit dem Debuggerfenster zu tun zu haben. Wenn Du experimentierfreudig bist, kannst den Parameter ja kopieren, einen auskommentieren und am anderen Drehen. Kaputtgehen kann dabei nix ;-)

Ratlos,
Bernhard

[werxs]

Hi,

da gab´s mal eine Diskussion im Lotus Forum auf LDD

http://www-10.lotus.com/ldd/46dom.nsf/DateAllThreadedweb/f3e3cdf5e14a829d85256c1a006f6efa?OpenDocument

...hat aber in der Tat wohl was mit dem Designer / Debugger zu tun...

Grüße
w.

[Yvi]

Danke ich hab den Eintrag jetzt einfach mal auskommentiert mal sehen was Notes jetzt sagt

Gruß
Yvi

[Heiggo]

Hab doch was in der

Lotus Software Knowledge Base
Technote

gefindelt :-)

Title:  
      Notes.ini Parameters: DesignWinSplitterPos and Debug_Disable_Repl_OPT appear after upgrade to 5.0.11
Product:   Lotus Domino  >  Lotus Domino Server  >  5.0.11
Platform(s):   Windows
     
Document Number:   1090790   Date:   28.08.2002


Problem
The following two Notes.ini parameters appear in Notes.ini and also in Log.nsf after server has been upgraded to 5.0.11

08/24/2002 10:27:59 AM   ;DebugWinSplitterPos=267
08/24/2002 10:27:59 AM   Debug_Disable_Repl_OPT=1
08/24/2002 10:27:59 AM  Warning: Debug parameters could impact operation or performance.

Customer did not enable any debugging nor did they manually added these parameters.




Solution
Debug_Disable_Repl_OPT

Debug_Disable_Repl_OPT=1 will change the search algorithm that returns a list of files to replicate.  When the optimization is disabled it will not have any
performance impact on the Domino server.

With the optimization there is a buffer that contains information about each database and is limited to 64k.  This is a buffer that is implemented to improve
performance.  With systems that use a large number of directories and databases, the INI parameter DEBUG_DISABLE_REPL_OPT=1 can be used to avoid
using the buffer.  This INI parameter forces the replicator task to perform a full scan of the data path, thereby avoiding the exclusion of databases because of
the buffer limit.  It should be noted that, if there is a recursive directory structure, this INI parameter will result in serious performance problems for the server.

The buffer contains 26 bytes of information related to each database (the database replication ID, etc.), plus a variable amount of data related to the actual
path of each database relative to the data directory.  Depending on the average size of the data path, this buffer can hold information for approximately 1500 -
2000 databases.  Obviously, if the average path length is excessively large, the number of databases held in the buffer would be much smaller.

In the case where replication was not replicating certain databases, the memory buffer that was allocated was too small to include all of the databases.  In
cases where the paths are long, it uses up more of the allocated memory than databases that are off the root of the data directory.  This may explain why you
can see different results on different servers.

DebugWinSplitterPos
When the Lotus Script Debugger is enabled or used, this parameter is used to define where the Windows Panes must appear on the screen.
The ini parameter is added by the debugger code so even if you remove it (or rem it out) once the debugger is used it will be put back in.


Supporting Information:

The DebugWinSplitterPos parameter will be shown in the Log.nsf even after you have tried to REM it out

Related Documents:





Historical Number: 194631
Keywords: Domino Server; Incident 1500596; Server; Installation; Procedure

[Yvi]

  Danke Schön  

Jetzt bin ich etwas schlauer.

Gruß
Yvi